8/2/2023 0 Comments Toy box hingesWe also offer a big discount to our customers. It’s worth the cost and helps you save money. We offer outstanding quality at a fair price. ![]() It is perfect for a wood project like a toy box. Both together could slow down a lid to less than 30 Lbs in a safe way. But Apexstone oil damper is more potent for some thick doors. Instructions Included, Screws Included.įeatures of Apexstone Soft Closing Hinge ☑Strong and SturdyĪpexstone sells the best soft close hinges in the market, our hinges for lids or cabinets have similar characteristics as Blum soft close hinges. Lid Size and Weight requirement: SOFT DOWN the door/ lid in which the SIDE LENGTH is Less than 30 Inches, the WEIGHT is Less than 30 Lbs.Force: A single Apexstone soft close gas strut is suitable for a lid of fewer than 16.5 LBS, and a pair(2 pieces) of gas struts is suitable for a lid of fewer than 33 LBS accordingly.Extended Length (hole center to hole center): 14.2 inch/ 360mm.There’s plenty of time to move little fingers out of the way. Our cabinet hinges with soft close gas spring ensure toy box safety and can also be used for other projects that require a soft-closing mechanism. With Apexstone Soft Close Lid Hinges, you can enjoy the peace of mind that comes with a gentle, slow closure that takes about 5 to 10 seconds to go from fully open to fully closed. Soft close feature is essential for safety, especially when it comes to lids and cabinets that may accidentally trap little fingers. More questions?, feel free to ask.Are you still worried about your child’s fingers getting smashed from the toy box lid? I believe that i attached a link to the project showing a slide show with several photof how I build this chest. In this project I used a piano hinge and a set of gas filled closing pistons. I have posted on "MY PROJECTS PAGE" a cedar chest that I build that shows how I build a lid similiar to the toy box lid I am describing. Because of how the hinge is made you will have to cut the mortise shallow to allow the hinge to stand proud of the surface or there will be some hinge binding. Using one to represent the lid and on to represent the box, mortise them into the material and then check for hinge binding. I believe a person could mortise the hinge however to be sure I would take a couple pieces of scrap wood of the same thichness as the box. Then on the back I added some molding to the box and cut it around the hinges running it up to near the closed lid. It also gave me the ability to fashion a handle in which to grasp in both opening and closing the lid. This also looked like a breadboard end so it also covered the end grain in the lid. This allowed me to place some felt stick on pads to the front corners to make the lid close silently. ![]() There was a gap about 1/8 " on the edges so I attached a molding to the lid around the two sides and the front that extended down covering the gap. ![]() Stephen, when I used them I attached them to the box without a mortise. Good luck with the building and be sure to post some photos of the project. They are available as are the other products at most woodworking supply stores such as Rocklers and Woodworkers supply. It gives a safe opening and closing lid with the least amount of troublesome installation. If you asked my preference I would go for the tortion spring hinge. I have used the lid support that fold like a knife but these were the worst as there is the danger of a child getting their fingers pinched in the folding action of the support and then they always seemed to get bent. I have used the spring tortion hinge made especially for the purpose of preventing falling lids which worked the best. These worked however seemed to be rather cumbersome once installed. I have used piano hinges with the soft closing gas filled dampers that prevent a falling lid. The finger smashing thing is always a concern and needs careful consideration. I have build a half dozen or so and the hinge is always a question as to what should be done. Stephen, building a toy box can be not only fun but rewarding to know that you are giving to the child a hand made gift that can become a favorite of not only the child but to the parents as they look back and remember your thought of a special gift made especially for their child.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |